No exemplo de validação atual, com base na NBC 2020{ %/#Referir [1]]] e
Base de dados de túneis de vento japonesas
para edifício baixo com inclinação de 45 graus. A configuração recomendada para cobertura plana tridimensional com beirais pontiagudos é descrita na próxima parte.
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
No exemplo de verificação, o cálculo de cargas de vento num edifício com cobertura de duas águas utilizando a norma EN 1991-1-4 é comparado com uma simulação CFD no RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
No exemplo de verificação, o cálculo da carga de vento num edifício com cobertura plana utilizando a norma EN 1991-1-4 é comparado com uma simulação CFD no RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
A simply supported beam is loaded by pure bending. Devido à encurvadura por flexão, tente determinar a carga de encurvadura crítica e o fator de carga correspondente.
A strut with a circular cross-section is supported according to four basic cases of Euler buckling and subjected to pressure force. Determine a carga de encurvadura crítica.
Considere o vão da barra ASTM A992 W 18×50 apresentado na Figura 01 e as cargas permanentes e variáveis uniformes. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Uma viga ASTM A992 W 24×62 com corte nas extremidades de 24 e 72,5 t das cargas permanente e variável, respetivamente, é apresentada na Figura 01. Verify the available shear strength of the selected beam, based on LRFD and ASD.
A column is composed of a concrete section (rectangle 100/200) and a steel section (profile I 200). Está sujeito a uma força de compressão. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Um quarto de barra circular com uma secção retangular é carregado com uma força fora do plano. This force causes a bending moment, torsional moment, and transverse force. While neglecting self-weight, determine the total deflection of the curved beam.
Uma viga curvada é constituída por duas vigas de secção retangular. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
A viga articulada de secção retangular é sujeita a cargas uniformes e deslocada verticalmente por excentricidade. Considering the small deformation theory, neglecting the self‑weight, and assuming that the beam is made of isotropic elastic material, determine the maximum deflection.
No meio do vão de uma viga de apoio simples, é aplicada uma força concentrada num determinado momento no tempo. Considering only the small deformation theory, determine the maximum deflection of the beam.
Uma força concentrada é aplicada durante um curto período de tempo no centro de uma viga de apoio simples. Considering only the small deformation theory and assuming that the mass of the beam is concentrated at its mid‑span, determine its maximum deflection.
Uma consola com secção circular é carregada por forças de flexão e rotação concentradas. The aim of this verification example is to compare the reduced stress according to the von Mises and Tresca theories.
A estrutura de pórticos de dois pisos está sujeita a cargas sísmicas. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Este exemplo serve para ilustrar o plano. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
A consola é carregada por um momento na sua extremidade livre. Using the geometrically linear analysis and large deformation analysis, and neglecting the beam's self-weight, determine the maximum deflections at the free end. The verification example is based on the example introduced by Gensichen and Lumpe.
A member with the given boundary conditions is loaded by torsional moment and axial force. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Compare estes valores ao mesmo tempo que aceita ou não considera a influência da força axial. The verification example is based on the example introduced by Gensichen and Lumpe.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. É apoiada de forma simples. The problem is described using the following parameters. Determine the deflections in the given test times.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. A superfície plástica é descrita de acordo com a teoria da plasticidade de Tsai-Wu.
Defina o momento fletor que irá curvar a barra na extremidade livre da consola. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
A viga está completamente fixada na extremidade esquerda (empenamento restringido) e apoiada na extremidade direita por um apoio de forquilha (empenamento possibilitado). The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
Uma viga articulada nas duas extremidades é carregada com força concentrada no meio. Neglecting its self-weight and shear stiffness, determine the beam's maximum deflection, normal force, and moment at the mid-span, assuming the second- and third-order analysis.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
É definida uma viga em consola com uma secção de viga em I de comprimento L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
A viga de aço de secção quadrada está sujeita a uma força normal e a uma carga distribuída. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
A viga de aço carregada axialmente com uma secção quadrada está apoiada sobre uma articulação numa das extremidades e sobre uma mola na outra extremidade. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Nas duas extremidades, está fixado um bloco tridimensional de material elástico-plástico. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.